Futek IPM52x (D520) Digital Display Manual de usuario

IPM525 (Old Model# D525) OPERATOR'S MANUAL 10 Thomas • Irvine, CA 92618 • 1-800-23-FUTEK Fax - (949) 465

9 h 4. EX K• UT, Y or SPEC), it exits to you back to RUN mode. ER key should be pushed first to store ENTER K• Ent h. tedly pushing • , it

10 > The unmarked yellow LED just above the Down/F4 key will light, indicating you are in the SETUP mode. • If no lockout code, “SETUP” flashe

11 D. FINE TUNE SCALE/SPAN Push and hold SETUP key, then UP arrow key pushed at the same time and then both keys released. This program allows

12 Example: Enter number 12 to skip DISPLY and SPEC branches from normal setup selections. Once number is entered, display will go to next

13 • “OutPut” (Only if OutPut is not disabled from above) is flashed with current selected number. Valid values 0-31. 0 Don’t disab

14 • • • • If EXIT key is push at any of the 6 main heading, exit back to run mode. If EXIT key is push while in a main branch, exit back to that m

15 SECTION 3.4: PROGRAMMING TIPS SELECT Key This represents SELECT key on flow charts ENTER Key This represents ENTER key on flow charts N

16 program branch heading SPEC, CODE menu. • The preset code (1-40) must be entered at this time. If wrong code is entered or if no code is entere

SECTION 3.6: MAIN PROGRAMMING BRANCHES 17 Chan1,Chan2,Chan3setup routines andcalibrations areunderthis main menu.Run ModePress the"ENTER&quo

18 SECTION 3.6 (cont.) "CODE" is displayed if a lock out code has been programmed. • • If "CODE", then enter your Lockout Code

1 Our recommendations, if any, for those of these products are based on tests believed to be reliable. The greatest care is exercised in the sele

19 high input values below. Push ENTER key to advance. 2. "dEC Pt" selects decimal point. Push SELECT key for displaying decimal point

20 4. "dSP Hi" (display high). Either select "yES" or "nO" If "yES" is selected, this allows you to appl

21 above selected math formulas. Push ENTER key to advance. c. "dEC Pt" selects decimal point. Push SELECT key for displaying decimal p

22 selection of "SAFE"(fail safe) selection. The selection "SAFE" here controls relays 1 through 3 for the fail safe operation.

23 alarm will remain on till manually reset. Use SELECT key to view “YES” for latching and “NO” for non-latching. Use the ENTER key to enter choice

24 b) "nET" net value c) "PEAK 1" peak 1 value • "CHAn 4" Channel 4 d) "Gross" gross value e) &

25 • • • • • • • • • Use SELECT key to choose which function you wish to program. Then press ENTER key. "F1 Set" thru "F4 Set"

26 C. "nEt" assigns F key to switch displayed channel between gross and net • Pushing F key will switch displayed channel to display ne

27 • Pushing F key for 4 seconds will reset the tare value to zero. ! "CHAn 1" assigns F key to display channel 1 ! "CHAn 2&

28 "CHAn 1", "CHAn 2". "CHAn 3" Select channel to do peak on 4. "Scale 2" setup Programs the setup and a

2 Table of Contents Section Topic Page Section 1 Introduction and Description Section 1.1 Product Description 3 Section 1

29 • Reset the meter to the user defined defaults "DEFAUL" default program prompt "YES"/"NO" "No"

30 returns to "SPEC" branch heading. 8. Resolution selection This allows user to select the resolution and speed. The selection applies

31 • Resolution - 16 bit D/A • Located on the option/top printed circuit board FEATURE P: • Excitation supplies of:  24VDC @150mA Accuracy

32 Impedance 50 Ohms 10 Mohm 10 Mohm 10 Mohm 10 Mohm 10 Mohm Resolution 1 uA 1 uV 10 uV 10 uV 100 uV 1 mV Over-range Capability, mini

3 SECTION 1 INTRODUCTION AND DESCRIPTION SECTION 1.1: UNIT DESCRIPTION: The single input IPM525 intelligent process meters features 5 ½ digit re

4 P2 (Option Board/Top Connector) P1 (Main Board /Bottom Connector) SECTION 1.3 FUSE SECTION 2

5 SECTION 2.0 SAFETY SUMMARY All safety related regulations, local codes and in structions that appear this literature or on equipment must be o

6 ANDSECTION 2.1: MAIN BOARD/BOTTOM (P1) OPTION BOARD/TOP (P2) PIN OUTS ERIAL RS-232C CONNECTIONS ON P1(MAIN SBD) CONNECTOR

7 ECTION 3 S ION AND PROGRAMMING OPERAT

8 SECTION 3.1: FRONT PANEL KEYS eyboard has two modes of operation - SETUP nd RUN ETUP MODE KEYS The front panel kaS EXI